E1 over Ethernet Converter, TDM over IP Multiplexer
STM-1 over Ethernet Multiplexer, STM-1 TDM over IP
SPOTLIGHT:
EthMux.SA63 can aggregate 63 E1 over IP remote services to 1 STM-1 port. Remote CPEs could be other members in Ethmux family such as EthMux SA16, EthMux SA1608, EthMux SA1601, EthMux SA1602, EthMux SA1604 etc. to run legacy E1 services.
DESCRIPTION：
As a cost effective solution for the traditional telecom services migrate to the IP packet networking technology, EthMux SA63 adopts the innovative TDM over IP technology, with IP circuit emulation that supports transportation of 1*STM-1 and 5 GE electrical ports and 1 GE optical port. The uplink ports and user data ports are IEEE 802.3 compliant, 10/100/1000M auto-sensed Ethernet ports.
State-of-the-art design provides the highest availability with the accurate timing signal and data bit stream reconstruction. Predefined system parameter profiles that according to different application requirement; ultimately simplify the installation process and saving the maintenance cost.
EthMux V16 are able to work together with other members in TDM over IP family such as EthMux SA16, EthMux SA1608, EthMux SA1601, EthMux SA1602, EthMux SA1604 etc. to run legacy E1 services. Telecom and Enterprise users can save a lot of access and equipment costs and generates new revenue by offering different types of services over their packet-switched infrastructure. It is also suitable for connecting to the wireless equipment to achieve fast deployment of E1/T1 services. One particular application is to build E1/T1 links with low cost Wireless LAN bridges, replacing much more costly microwave radios. Operators can use EthMux to provide legacy TDM services over wired or wireless Ethernet/IP network.
FEATURES:
1. Provide 1 channel STM-1(63 E1 service) over 1 Ethernet adaptive
2. Provide 5 GE electrical ports（two ports are uplink ports and the other three are local data ports，Anyone of 5 GE electrical ports may act as NM port), and 1 GE optical port ( used as either uplink port or local data port.)
3. support SAToP protocol, Ethernet encapsulation support IP/UDP., support E1 Qos
4. E1 clock supports 3 mode: local clock, adaptive and loopback
5. Provide 2 STM-1 optical ports , Support 1 + 1 protection
6. Ethernet built-in layer 2 switch, support VLAN802.1Q based and QinQ based), port based、8021.1P based and TOS based) Support port speed limited, flow control, MAC address automatic learning and MAC address aging time set;
7. High transmission efficiency, low transmission delay
8. Frequency reduction stability, low jitter and drifting
9. Resist to packet loss, no jump frequency， with frame synchronization protection,
10. Enough jitter buffer to resist packet delay variation (PDV)
11. User-friendly Web server supported for easy setup and maintenance
12. Support SNMP network management (V2 version )
13. Support Local and remote Software and hardware online upgrade
14. Support SNTP network time setting
15. Support software test E1 error
16. support AC 100 ~ 260 V and DC-48 V dual power supply, realize 1 + 1 backup
Specification:
Item |
Description |
|
Model |
EthMux.SA63 |
2 PWR slots 1 STM-1 slot 1 Ethernet uplink slot 1 External clock interface |
Service card |
Ethernet uplink card |
5 GE electrical ports and 1 GE optical port Comply with IEEE 802.3, 802.1Q, 802.1P, 802.3x Speed and duplex auto-negotiation or manual |
STM-1 card |
2 port Default SC/PC |
|
Power |
Supply |
2 power slots |
AC 220v power module |
||
AC 110v power module |
||
DC -48v power module |
||
Consumption |
≤40W |
|
Working Environment |
Temperature |
0~ 50°C |
Relative Humidity |
≤90% (non-condensing) |
|
Dimension |
W x H x D (mm): |
1U: 440 x 44 x 231 (mm) |
Typical Application:
